/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.0.12-76060006-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Silicon Motion based SSDs Device Model: KingDian S400 120GB Serial Number: -- Firmware Version: S0509A0 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Jan 9 12:48:43 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. No failed Attributes found. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 050 - 0 5 Reallocated_Sector_Ct -O--CK 100 100 050 - 0 9 Power_On_Hours -O--CK 100 100 050 - 5693 12 Power_Cycle_Count -O--CK 100 100 050 - 3771 160 Uncorrectable_Error_Cnt -O--CK 100 100 050 - 0 161 Valid_Spare_Block_Cnt PO--CK 100 100 050 - 100 163 Initial_Bad_Block_Count -O--CK 100 100 050 - 12 164 Total_Erase_Count -O--CK 100 100 050 - 890124 165 Max_Erase_Count -O--CK 100 100 050 - 5432 166 Min_Erase_Count -O--CK 100 100 050 - 105 167 Average_Erase_Count -O--CK 100 100 050 - 608 168 Max_Erase_Count_of_Spec -O--CK 100 100 050 - 5050 169 Remaining_Lifetime_Perc -O--CK 100 100 050 - 88 175 Program_Fail_Count_Chip -O--CK 100 100 050 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 050 - 0 177 Wear_Leveling_Count -O--CK 100 100 050 - 0 178 Runtime_Invalid_Blk_Cnt -O--CK 100 100 050 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 050 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 050 - 0 192 Power-Off_Retract_Count -O--CK 100 100 050 - 3292 194 Temperature_Celsius -O---K 100 100 050 - 40 195 Hardware_ECC_Recovered -O--CK 100 100 050 - 0 196 Reallocated_Event_Count -O--CK 100 100 050 - 0 197 Current_Pending_Sector -O--CK 100 100 050 - 0 198 Offline_Uncorrectable -O--CK 100 100 050 - 0 232 Available_Reservd_Space -O--CK 100 100 050 - 100 241 Host_Writes_32MiB ----CK 100 100 050 - 530431 242 Host_Reads_32MiB ----CK 100 100 050 - 522278 245 TLC_Writes_32MiB -O--CK 100 100 050 - 811650 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xde GPL VS 8 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 13 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 13 [0] log entry is empty Error 12 [3] log entry is empty Error 11 [2] log entry is empty Error 10 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d1 01 01 00 00 4f 00 c2 01 00 08 00:00:00.000 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] 2f 00 00 01 01 00 00 00 00 00 03 00 08 00:00:00.000 READ LOG EXT 2f 00 00 01 01 00 00 00 00 00 00 00 08 00:00:00.000 READ LOG EXT b0 00 d5 01 01 00 00 4f 00 c2 00 00 08 00:00:00.000 SMART READ LOG b0 00 da 00 00 00 00 4f 00 c2 00 00 08 00:00:00.000 SMART RETURN STATUS SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 5676 - # 2 Extended offline Completed without error 00% 5601 - # 3 Extended offline Completed without error 00% 5369 - # 4 Extended offline Completed without error 00% 5254 - # 5 Extended offline Completed without error 00% 5207 - # 6 Extended offline Completed without error 00% 5189 - # 7 Extended offline Completed without error 00% 5146 - # 8 Short offline Aborted by host 90% 5145 - # 9 Short offline Aborted by host 90% 5145 - #10 Short offline Aborted by host 90% 5145 - #11 Extended offline Completed without error 00% 5119 - #12 Extended offline Aborted by host 80% 5106 - #13 Extended offline Aborted by host 80% 5106 - #14 Extended offline Completed without error 00% 5095 - #15 Short offline Completed without error 00% 5079 - #16 Extended offline Completed without error 00% 5052 - #17 Extended offline Completed without error 00% 5039 - #18 Short offline Aborted by host 90% 5039 - #19 Short offline Aborted by host 90% 5039 - Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 3771 --- Lifetime Power-On Resets 0x01 0x010 4 5693 --- Power-on Hours 0x01 0x018 6 402602560 --- Logical Sectors Written 0x01 0x020 6 5 --- Number of Write Commands 0x01 0x028 6 4163291610 --- Logical Sectors Read 0x01 0x030 6 1901 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 12 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x000a 4 4 Device-to-host register FISes sent due to a COMRESET /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.0.12-76060006-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Elements / My Passport (USB, AF) Device Model: WDC WD5000LMVW-11VEDS3 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Jan 9 12:48:43 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 127 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9840) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 113) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 45 3 Spin_Up_Time POS--K 120 113 021 - 2975 4 Start_Stop_Count -O--CK 094 094 000 - 6032 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 093 093 000 - 5178 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1470 192 Power-Off_Retract_Count -O--CK 199 199 000 - 910 193 Load_Cycle_Count -O--CK 159 159 000 - 123450 194 Temperature_Celsius -O---K 114 089 000 - 29 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 1 198 Offline_Uncorrectable ----CK 200 200 000 - 1 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 38 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 45 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 45 [20] occurred at disk power-on lifetime: 3665 hours (152 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 37 34 a3 5f 40 00 Error: UNC 1 sectors at LBA = 0x3734a35f = 926196575 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 00 01 00 00 37 34 a3 5f 40 00 18:12:43.817 READ DMA EXT 25 00 d5 00 18 00 00 01 86 06 a8 40 00 18:12:43.816 READ DMA EXT 25 00 d5 00 08 00 00 01 f0 42 28 40 00 18:12:43.802 READ DMA EXT 25 00 d5 00 38 00 00 01 8d ba 90 40 00 18:12:43.801 READ DMA EXT 25 00 d5 00 30 00 00 01 8d ba 60 40 00 18:12:43.689 READ DMA EXT Error 44 [19] occurred at disk power-on lifetime: 3665 hours (152 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 37 34 a3 5f 40 00 Error: UNC 1 sectors at LBA = 0x3734a35f = 926196575 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 00 01 00 00 37 34 a3 5f 40 00 18:12:40.123 READ DMA EXT 25 00 d5 00 08 00 00 01 86 06 a0 40 00 18:12:40.117 READ DMA EXT 25 00 d5 00 08 00 00 01 f0 2b 08 40 00 18:12:40.107 READ DMA EXT 25 00 d5 00 38 00 00 01 8d ba 28 40 00 18:12:40.104 READ DMA EXT 25 00 d5 00 80 00 00 01 8d b5 78 40 00 18:12:40.102 READ DMA EXT Error 43 [18] occurred at disk power-on lifetime: 3665 hours (152 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 37 34 a3 5f 40 00 Error: UNC 1 sectors at LBA = 0x3734a35f = 926196575 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 00 01 00 00 37 34 a3 5f 40 00 18:12:36.410 READ DMA EXT 25 00 d5 00 08 00 00 01 bf 10 98 40 00 18:12:36.397 READ DMA EXT 25 00 d5 00 38 00 00 02 2e 79 70 40 00 18:12:36.383 READ DMA EXT 25 00 d5 00 08 00 00 01 f0 26 08 40 00 18:12:36.375 READ DMA EXT 25 00 d5 00 40 00 00 00 aa 08 58 40 00 18:12:36.374 READ DMA EXT Error 42 [17] occurred at disk power-on lifetime: 3665 hours (152 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 37 34 a3 5f 40 00 Error: UNC 1 sectors at LBA = 0x3734a35f = 926196575 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 00 01 00 00 37 34 a3 5f 40 00 18:12:32.692 READ DMA EXT 25 00 d5 00 30 00 00 01 86 85 c0 40 00 18:12:32.691 READ DMA EXT 25 00 d5 00 08 00 00 01 e1 be a8 40 00 18:12:32.683 READ DMA EXT 25 00 d5 00 08 00 00 00 aa 08 50 40 00 18:12:32.661 READ DMA EXT 25 00 d5 00 60 00 00 01 8d b3 58 40 00 18:12:32.659 READ DMA EXT Error 41 [16] occurred at disk power-on lifetime: 3665 hours (152 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 37 34 a3 5f 40 00 Error: UNC 1 sectors at LBA = 0x3734a35f = 926196575 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 00 01 00 00 37 34 a3 5f 40 00 18:12:28.986 READ DMA EXT 35 00 d5 00 08 00 00 01 fd 88 30 40 00 18:12:28.985 WRITE DMA EXT 25 00 d5 00 08 00 00 01 86 85 10 40 00 18:12:28.970 READ DMA EXT 25 00 d5 00 08 00 00 03 4a d3 78 40 00 18:12:28.960 READ DMA EXT 25 00 d5 00 08 00 00 01 e1 ba a8 40 00 18:12:28.951 READ DMA EXT Error 40 [15] occurred at disk power-on lifetime: 3665 hours (152 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 37 34 a3 5e 40 00 Error: UNC 1 sectors at LBA = 0x3734a35e = 926196574 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 00 01 00 00 37 34 a3 5e 40 00 18:12:25.250 READ DMA EXT 25 00 d5 00 10 00 00 00 51 dd d8 40 00 18:12:25.244 READ DMA EXT 25 00 d5 00 08 00 00 00 aa 0a e0 40 00 18:12:25.232 READ DMA EXT 35 00 d5 00 10 00 00 01 ba 4c 70 40 00 18:12:25.232 WRITE DMA EXT 35 00 d5 00 d0 00 00 05 8b 28 40 40 00 18:12:25.228 WRITE DMA EXT Error 39 [14] occurred at disk power-on lifetime: 3665 hours (152 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 37 34 a3 5e 40 00 Error: UNC 1 sectors at LBA = 0x3734a35e = 926196574 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 00 01 00 00 37 34 a3 5e 40 00 18:12:21.530 READ DMA EXT 35 00 d5 00 08 00 00 05 8b 2a f8 40 00 18:12:21.530 WRITE DMA EXT 35 00 d5 00 08 00 00 05 8b 2a f0 40 00 18:12:21.529 WRITE DMA EXT 25 00 d5 00 08 00 00 01 f0 00 a0 40 00 18:12:21.516 READ DMA EXT 25 00 d5 00 08 00 00 02 2e f3 50 40 00 18:12:21.485 READ DMA EXT Error 38 [13] occurred at disk power-on lifetime: 3665 hours (152 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 37 34 a3 5e 40 00 Error: UNC 1 sectors at LBA = 0x3734a35e = 926196574 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d5 00 01 00 00 37 34 a3 5e 40 00 18:12:17.529 READ DMA EXT 25 00 d5 00 08 00 00 01 8d ac 78 40 00 18:12:17.521 READ DMA EXT 35 00 d5 00 10 00 00 00 51 90 68 40 00 18:12:17.521 WRITE DMA EXT 35 00 d5 00 10 00 00 00 51 8c 38 40 00 18:12:17.519 WRITE DMA EXT 35 00 d5 00 10 00 00 00 51 88 d8 40 00 18:12:17.518 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed without error 00% 5126 - # 2 Extended offline Completed: read failure 50% 5126 483433880 # 3 Short offline Completed without error 00% 5125 - # 4 Conveyance offline Completed: read failure 90% 5117 483433880 # 5 Short offline Completed: read failure 90% 5117 483433880 # 6 Extended offline Completed: read failure 90% 5117 483433880 # 7 Short offline Completed: read failure 90% 3378 926196568 # 8 Short offline Completed: read failure 90% 3378 926196568 # 9 Conveyance offline Completed: read failure 90% 3378 926196568 #10 Extended offline Completed: read failure 90% 3353 926196568 #11 Conveyance offline Completed: read failure 90% 3353 926196568 #12 Short offline Completed without error 00% 3001 - #13 Conveyance offline Completed without error 00% 3000 - #14 Extended offline Interrupted (host reset) 60% 1362 - #15 Conveyance offline Completed without error 00% 1273 - #16 Extended offline Completed without error 00% 1271 - #17 Conveyance offline Aborted by host 80% 1269 - #18 Extended offline Aborted by host 50% 970 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 27/36 Celsius Lifetime Min/Max Temperature: 0/54 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (90) Index Estimated Time Temperature Celsius 91 2023-01-09 10:41 33 ************** ... ..( 4 skipped). .. ************** 96 2023-01-09 10:46 33 ************** 97 2023-01-09 10:47 34 *************** ... ..( 12 skipped). .. *************** 110 2023-01-09 11:00 34 *************** 111 2023-01-09 11:01 35 **************** ... ..( 17 skipped). .. **************** 1 2023-01-09 11:19 35 **************** 2 2023-01-09 11:20 36 ***************** ... ..( 38 skipped). .. ***************** 41 2023-01-09 11:59 36 ***************** 42 2023-01-09 12:00 35 **************** 43 2023-01-09 12:01 35 **************** 44 2023-01-09 12:02 34 *************** 45 2023-01-09 12:03 34 *************** 46 2023-01-09 12:04 33 ************** 47 2023-01-09 12:05 33 ************** 48 2023-01-09 12:06 32 ************* 49 2023-01-09 12:07 32 ************* 50 2023-01-09 12:08 31 ************ ... ..( 7 skipped). .. ************ 58 2023-01-09 12:16 31 ************ 59 2023-01-09 12:17 30 *********** ... ..( 7 skipped). .. *********** 67 2023-01-09 12:25 30 *********** 68 2023-01-09 12:26 29 ********** ... ..( 21 skipped). .. ********** 90 2023-01-09 12:48 29 ********** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 9105 Vendor specific