/dev/sda smartctl 7.2 2020-12-30 r5155 [i686-linux-5.10.0-35-686-pae] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD1600BEVT-22ZCT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 11.01A11 User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Wed Oct 1 15:09:59 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 59) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 242 3 Spin_Up_Time POS--K 159 154 021 - 1016 4 Start_Stop_Count -O--CK 097 097 000 - 3978 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 087 087 000 - 9986 10 Spin_Retry_Count PO--CK 100 098 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3208 192 Power-Off_Retract_Count -O--CK 200 200 000 - 519 193 Load_Cycle_Count -O--CK 104 104 000 - 290239 194 Temperature_Celsius -O---K 103 083 000 - 40 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 100 253 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 37 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 37 [12] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 43 25 01 1a 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 20 00 00 5f 01 36 00 1a 25 00 00 00 00:01:01.192 NOP [Abort queued commands] 00 2c 25 01 1a 00 20 00 b7 00 00 00 00 00:01:12.245 NOP [Reserved subcommand] [OBS-ACS-2] 00 40 00 00 3f 01 2c 00 1a 25 00 00 00 00:00:12.040 NOP [Abort queued commands] Error 36 [11] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 3e 25 25 3a 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 2f 24 d8 00 b0 35 00 00 00 00:01:01.192 NOP [Abort queued commands] 00 d8 35 24 b0 00 08 00 47 00 00 00 00 00:40:04.568 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 6f 24 fc 00 a6 35 00 00 00 00:00:59.152 NOP [Abort queued commands] Error 35 [10] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 32 25 06 cf 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 50 00 00 37 06 12 00 cf 35 00 00 00 00:01:01.192 NOP [Abort queued commands] 00 11 35 06 cf 00 08 00 7f 00 00 00 00 00:07:26.225 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 77 06 ec 00 ce 25 00 00 00 00:00:34.576 NOP [Abort queued commands] Error 34 [9] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 33 25 06 bf 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 27 06 29 00 bf 25 00 00 00 00:01:01.192 NOP [Abort queued commands] 02 0c 25 06 bf 00 60 00 77 00 00 00 02 00:07:22.136 [RESERVED] 00 08 00 00 7f 06 0c 00 bf 25 00 00 00 00:00:26.656 NOP [Abort queued commands] Error 33 [8] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 bf 25 06 aa 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 3f 06 b4 00 aa 35 00 00 00 00:01:01.192 NOP [Abort queued commands] 00 a0 25 06 aa 00 08 00 7f 00 00 00 00 00:07:16.908 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 00 00 7f 06 9c 00 aa 35 00 00 00 00:00:57.168 NOP [Abort queued commands] Error 32 [7] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 5c 25 06 9d 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 20 00 00 53 06 3c 0d 9d 25 00 00 00 00:01:01.192 NOP [Abort queued commands] 0d 37 25 06 9d 00 20 00 c3 00 00 00 00 00:07:13.464 [RESERVED] 00 20 00 00 83 06 37 0d 9d 25 00 00 00 00:01:03.240 NOP [Abort queued commands] Error 31 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 c5 25 06 7f 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 18 00 00 27 06 c4 00 7f 35 00 00 00 00:01:01.192 NOP [Abort queued commands] 00 9b 25 06 7f 00 40 00 17 00 00 00 0d 00:07:05.900 NOP [Reserved subcommand] [OBS-ACS-2] 00 40 00 00 5f 06 83 0b 7f 25 00 00 00 00:00:54.048 NOP [Abort queued commands] Error 30 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 46 25 06 68 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 3f 06 45 00 68 35 00 00 00 00:01:01.192 NOP [Abort queued commands] 00 1a ea 06 68 00 80 00 1f 00 00 00 00 00:06:59.897 NOP [Reserved subcommand] [OBS-ACS-2] 00 40 00 00 87 06 19 0d 68 25 00 00 00 00:00:00.000 NOP [Abort queued commands] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 36/45 Celsius Lifetime Min/Max Temperature: 38/61 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: 1/85 Celsius Temperature History Size (Index): 128 (111) Index Estimated Time Temperature Celsius 112 2025-10-01 13:03 43 ************************ 113 2025-10-01 13:04 42 *********************** 114 2025-10-01 13:05 43 ************************ 115 2025-10-01 13:06 42 *********************** ... ..( 5 skipped). .. *********************** 121 2025-10-01 13:12 42 *********************** 122 2025-10-01 13:13 41 ********************** ... ..( 3 skipped). .. ********************** 126 2025-10-01 13:17 41 ********************** 127 2025-10-01 13:18 40 ********************* ... ..( 9 skipped). .. ********************* 9 2025-10-01 13:28 40 ********************* 10 2025-10-01 13:29 39 ******************** 11 2025-10-01 13:30 40 ********************* 12 2025-10-01 13:31 39 ******************** ... ..( 11 skipped). .. ******************** 24 2025-10-01 13:43 39 ******************** 25 2025-10-01 13:44 38 ******************* ... ..( 37 skipped). .. ******************* 63 2025-10-01 14:22 38 ******************* 64 2025-10-01 14:23 39 ******************** 65 2025-10-01 14:24 38 ******************* ... ..( 2 skipped). .. ******************* 68 2025-10-01 14:27 38 ******************* 69 2025-10-01 14:28 39 ******************** 70 2025-10-01 14:29 38 ******************* 71 2025-10-01 14:30 38 ******************* 72 2025-10-01 14:31 39 ******************** ... ..( 27 skipped). .. ******************** 100 2025-10-01 14:59 39 ******************** 101 2025-10-01 15:00 38 ******************* 102 2025-10-01 15:01 39 ******************** ... ..( 2 skipped). .. ******************** 105 2025-10-01 15:04 39 ******************** 106 2025-10-01 15:05 40 ********************* ... ..( 4 skipped). .. ********************* 111 2025-10-01 15:10 40 ********************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x8000 4 14595 Vendor specific