/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.14-desktop-1omv4002] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device Model: ST3320613AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: SD22 User Capacity: 320,071,851,520 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Dec 22 14:32:31 2022 GMT ==> WARNING: There are known problems with these drives, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/207951en http://knowledge.seagate.com/articles/en_US/FAQ/207957en SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 609) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 68) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 119 099 006 - 226289221 3 Spin_Up_Time PO---- 097 096 000 - 0 4 Start_Stop_Count -O--CK 090 090 020 - 10775 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 5 7 Seek_Error_Rate POSR-- 090 060 030 - 1197348160 9 Power_On_Hours -O--CK 053 053 000 - 41380 10 Spin_Retry_Count PO--C- 100 100 097 - 87 12 Power_Cycle_Count -O--CK 093 093 020 - 7898 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 002 002 000 - 98 188 Command_Timeout -O--CK 100 091 000 - 249112166545 189 High_Fly_Writes -O-RCK 001 001 000 - 2238 190 Airflow_Temperature_Cel -O---K 066 052 045 - 34 (Min/Max 30/34) 194 Temperature_Celsius -O---K 034 048 000 - 34 (0 15 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 044 021 000 - 226289221 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 129 000 - 29641 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2819 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 112 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 112 [11] occurred at disk power-on lifetime: 38417 hours (1600 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 00 05 bc 00 00 Error: UNC at LBA = 0x1a0005bc = 436209084 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 1a 00 05 a0 e0 00 02:17:51.142 READ DMA EXT 35 00 00 00 10 00 01 b9 00 8a c0 e0 00 02:17:51.141 WRITE DMA EXT 25 00 00 00 10 00 00 f0 00 af e0 e0 00 02:17:51.140 READ DMA EXT 35 00 00 00 20 00 05 31 00 9a 20 e0 00 02:17:51.139 WRITE DMA EXT 35 00 00 00 20 00 01 b9 00 8a a0 e0 00 02:17:51.139 WRITE DMA EXT Error 111 [10] occurred at disk power-on lifetime: 38417 hours (1600 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 00 05 bc 00 00 Error: UNC at LBA = 0x1a0005bc = 436209084 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 1a 00 05 a0 e0 00 02:17:27.386 READ DMA EXT 35 00 00 00 10 00 01 5f 00 84 e0 e0 00 02:17:27.385 WRITE DMA EXT 25 00 00 00 10 00 01 8e 00 8c 40 e0 00 02:17:27.384 READ DMA EXT 35 00 00 00 20 00 05 2f 00 9a c0 e0 00 02:17:27.384 WRITE DMA EXT 35 00 00 00 20 00 01 5f 00 84 c0 e0 00 02:17:27.383 WRITE DMA EXT Error 110 [9] occurred at disk power-on lifetime: 38417 hours (1600 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 00 05 bc 00 00 Error: UNC at LBA = 0x1a0005bc = 436209084 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 1a 00 05 a0 e0 00 02:16:52.792 READ DMA EXT 35 00 00 00 10 00 01 8e 00 8c 40 e0 00 02:16:52.791 WRITE DMA EXT 25 00 00 00 10 00 00 c0 00 8d 80 e0 00 02:16:52.791 READ DMA EXT 35 00 00 00 20 00 05 2d 00 9a c0 e0 00 02:16:52.790 WRITE DMA EXT 35 00 00 00 20 00 01 8e 00 8c 20 e0 00 02:16:52.789 WRITE DMA EXT Error 109 [8] occurred at disk power-on lifetime: 38417 hours (1600 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 00 05 bc 00 00 Error: UNC at LBA = 0x1a0005bc = 436209084 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 1a 00 05 a0 e0 00 02:13:34.976 READ DMA EXT 35 00 00 00 10 00 01 66 00 80 e0 e0 00 02:13:34.976 WRITE DMA EXT 25 00 00 00 10 00 00 ff 00 96 c0 e0 00 02:13:34.975 READ DMA EXT 35 00 00 00 20 00 05 92 00 8f c0 e0 00 02:13:34.975 WRITE DMA EXT 35 00 00 00 20 00 01 66 00 80 c0 e0 00 02:13:34.974 WRITE DMA EXT Error 108 [7] occurred at disk power-on lifetime: 38410 hours (1600 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 00 05 bc 00 00 Error: UNC at LBA = 0x1a0005bc = 436209084 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 1a 00 05 a0 e0 00 03:27:38.440 READ DMA EXT 35 00 00 00 10 00 01 cd 00 9e 60 e0 00 03:27:38.439 WRITE DMA EXT 25 00 00 00 10 00 01 b9 00 8a c0 e0 00 03:27:38.438 READ DMA EXT 35 00 00 00 20 00 05 ff 00 79 40 e0 00 03:27:38.438 WRITE DMA EXT 35 00 00 00 20 00 01 cd 00 9e 40 e0 00 03:27:38.437 WRITE DMA EXT Error 107 [6] occurred at disk power-on lifetime: 38410 hours (1600 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 00 05 bc 00 00 Error: UNC at LBA = 0x1a0005bc = 436209084 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 1a 00 05 a0 e0 00 03:27:06.500 READ DMA EXT 35 00 00 00 10 00 01 b9 00 8a c0 e0 00 03:27:06.498 WRITE DMA EXT 25 00 00 00 10 00 00 ce 00 6f e0 e0 00 03:27:06.498 READ DMA EXT 35 00 00 00 20 00 05 fd 00 79 a0 e0 00 03:27:06.497 WRITE DMA EXT 35 00 00 00 20 00 01 b9 00 8a a0 e0 00 03:27:06.497 WRITE DMA EXT Error 106 [5] occurred at disk power-on lifetime: 38410 hours (1600 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 00 05 bc 00 00 Error: UNC at LBA = 0x1a0005bc = 436209084 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 1a 00 05 a0 e0 00 03:25:14.530 READ DMA EXT 35 00 00 00 80 00 03 c0 00 84 c0 e0 00 03:25:14.529 WRITE DMA EXT 35 00 00 00 20 00 05 fb 00 79 60 e0 00 03:25:14.529 WRITE DMA EXT 35 00 00 00 80 00 03 c0 00 84 40 e0 00 03:25:14.480 WRITE DMA EXT 35 00 00 01 00 00 05 32 00 7d a0 e0 00 03:25:14.479 WRITE DMA EXT Error 105 [4] occurred at disk power-on lifetime: 38410 hours (1600 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1a 00 05 bc 00 00 Error: UNC at LBA = 0x1a0005bc = 436209084 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1a 00 05 b8 e0 00 03:25:11.141 READ DMA EXT 25 00 00 00 08 00 00 1a 00 05 b0 e0 00 03:25:11.140 READ DMA EXT 35 00 00 00 80 00 03 bf 00 84 c0 e0 00 03:25:11.140 WRITE DMA EXT 25 00 00 00 08 00 00 1a 00 05 a8 e0 00 03:25:11.139 READ DMA EXT 35 00 00 00 80 00 03 bf 00 84 40 e0 00 03:25:11.138 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 30/34 Celsius Lifetime Min/Max Temperature: 15/48 Celsius Under/Over Temperature Limit Count: 0/9 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (60) Index Estimated Time Temperature Celsius 61 2022-12-22 12:25 38 ******************* ... ..( 6 skipped). .. ******************* 68 2022-12-22 12:32 38 ******************* 69 2022-12-22 12:33 ? - 70 2022-12-22 12:34 28 ********* 71 2022-12-22 12:35 29 ********** 72 2022-12-22 12:36 30 *********** 73 2022-12-22 12:37 30 *********** 74 2022-12-22 12:38 31 ************ 75 2022-12-22 12:39 32 ************* 76 2022-12-22 12:40 32 ************* 77 2022-12-22 12:41 33 ************** 78 2022-12-22 12:42 34 *************** 79 2022-12-22 12:43 34 *************** 80 2022-12-22 12:44 34 *************** 81 2022-12-22 12:45 35 **************** 82 2022-12-22 12:46 35 **************** 83 2022-12-22 12:47 36 ***************** ... ..( 2 skipped). .. ***************** 86 2022-12-22 12:50 36 ***************** 87 2022-12-22 12:51 37 ****************** ... ..( 5 skipped). .. ****************** 93 2022-12-22 12:57 37 ****************** 94 2022-12-22 12:58 38 ******************* ... ..( 16 skipped). .. ******************* 111 2022-12-22 13:15 38 ******************* 112 2022-12-22 13:16 37 ****************** 113 2022-12-22 13:17 37 ****************** 114 2022-12-22 13:18 38 ******************* 115 2022-12-22 13:19 37 ****************** ... ..( 7 skipped). .. ****************** 123 2022-12-22 13:27 37 ****************** 124 2022-12-22 13:28 ? - 125 2022-12-22 13:29 37 ****************** 126 2022-12-22 13:30 38 ******************* ... ..( 17 skipped). .. ******************* 16 2022-12-22 13:48 38 ******************* 17 2022-12-22 13:49 ? - 18 2022-12-22 13:50 38 ******************* ... ..( 10 skipped). .. ******************* 29 2022-12-22 14:01 38 ******************* 30 2022-12-22 14:02 ? - 31 2022-12-22 14:03 38 ******************* ... ..( 13 skipped). .. ******************* 45 2022-12-22 14:17 38 ******************* 46 2022-12-22 14:18 ? - 47 2022-12-22 14:19 38 ******************* ... ..( 2 skipped). .. ******************* 50 2022-12-22 14:22 38 ******************* 51 2022-12-22 14:23 ? - 52 2022-12-22 14:24 30 *********** 53 2022-12-22 14:25 30 *********** 54 2022-12-22 14:26 31 ************ 55 2022-12-22 14:27 31 ************ 56 2022-12-22 14:28 32 ************* 57 2022-12-22 14:29 32 ************* 58 2022-12-22 14:30 33 ************** 59 2022-12-22 14:31 33 ************** 60 2022-12-22 14:32 34 *************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.14-desktop-1omv4002] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus Device Model: ST3160023AS Serial Number: -- Firmware Version: 3.00 User Capacity: 160,040,803,840 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-6 T13/1410D revision 2 Local Time is: Thu Dec 22 14:32:31 2022 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 94) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 053 046 006 - 168528379 3 Spin_Up_Time PO---- 097 096 000 - 0 4 Start_Stop_Count -O--CK 091 091 020 - 9267 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 11 7 Seek_Error_Rate POSR-- 087 060 030 - 539017523 9 Power_On_Hours -O--CK 070 070 000 - 26746 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 092 092 020 - 8295 194 Temperature_Celsius -O---K 034 054 000 - 34 (0 11 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 053 046 000 - 168528379 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 001 000 - 10522 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 097 250 000 - 3 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory not supported SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 SL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 SL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x20 SL R/O 1 Streaming performance log [OBS-8] 0x21 SL R/O 1 Write stream error log 0x22 SL R/O 1 Read stream error log 0x23 SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f SL R/W 16 Host vendor specific log 0xa0 SL VS 1 Device vendor specific log 0xa1 SL VS 20 Device vendor specific log 0xa2 SL VS 101 Device vendor specific log 0xa8 SL VS 20 Device vendor specific log 0xa9 SL VS 1 Device vendor specific log SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 ATA Error Count: 11150 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 11150 occurred at disk power-on lifetime: 26605 hours (1108 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 08 68 96 a1 e0 Error: IDNF 8 sectors at LBA = 0x00a19668 = 10589800 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 68 96 a1 e0 00 02:15:35.552 READ DMA EXT 25 00 01 00 00 00 e0 00 02:15:35.552 READ DMA EXT 25 00 02 06 1c 20 e0 00 02:15:35.551 READ DMA EXT 25 00 06 00 1c 20 e0 00 02:15:35.551 READ DMA EXT 25 00 06 82 4b a1 e0 00 02:15:45.594 READ DMA EXT Error 11149 occurred at disk power-on lifetime: 26484 hours (1103 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 08 68 96 a1 e0 Error: IDNF 8 sectors at LBA = 0x00a19668 = 10589800 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 68 96 a1 e0 00 00:01:12.349 READ DMA EXT 25 00 01 00 00 00 e0 00 00:01:12.338 READ DMA EXT 25 00 02 06 1c 20 e0 00 00:01:21.052 READ DMA EXT 25 00 06 00 1c 20 e0 00 00:01:21.051 READ DMA EXT 25 00 08 80 87 a1 e0 00 00:01:20.802 READ DMA EXT Error 11148 occurred at disk power-on lifetime: 26013 hours (1083 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 07 c7 b7 21 e0 Error: UNC 7 sectors at LBA = 0x0021b7c7 = 2209735 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 c0 b7 21 e0 00 03:24:28.429 READ DMA EXT ea 00 00 00 00 00 a0 00 03:24:28.429 FLUSH CACHE EXT 35 00 08 c0 2e 4b e0 00 03:24:28.406 WRITE DMA EXT 35 00 08 1a 4a 22 e0 00 03:24:28.465 WRITE DMA EXT 35 00 08 12 4a 22 e0 00 03:24:28.431 WRITE DMA EXT Error 11147 occurred at disk power-on lifetime: 26013 hours (1083 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 07 c7 b7 21 e0 Error: UNC 7 sectors at LBA = 0x0021b7c7 = 2209735 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 40 c0 b7 21 e0 00 03:24:24.362 READ DMA EXT 35 00 20 60 72 85 e0 00 03:24:24.362 WRITE DMA EXT 35 00 20 00 94 87 e0 00 03:24:24.362 WRITE DMA EXT 25 00 20 c0 30 68 e0 00 03:24:24.361 READ DMA EXT 35 00 70 88 c2 6a e0 00 03:24:24.361 WRITE DMA EXT Error 11146 occurred at disk power-on lifetime: 25926 hours (1080 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 07 c7 b7 21 e0 Error: UNC 7 sectors at LBA = 0x0021b7c7 = 2209735 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 c0 b7 21 e0 00 02:33:27.036 READ DMA EXT 35 00 d0 d0 2e 4d e0 00 02:33:27.036 WRITE DMA EXT 35 00 08 c0 2e 4b e0 00 02:33:27.025 WRITE DMA EXT 25 00 20 00 53 d6 e0 00 02:33:27.025 READ DMA EXT 35 00 08 48 18 4c e0 00 02:33:23.130 WRITE DMA EXT SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported